Every part. Every connection.
Engineered together.

Overview

A factory-laminated PDLC unit on low-iron substrate. Sealed at the edge with TOSSEAL 381, supplied with two busbar pigtails. Installs into any standard 14 mm glazing rebate. The base build of the PRIVASEE smart-glass programme.

Build-up

6 + 0.8 + 0.4 + 0.8 + 6 mm — 14.0 mm nominal · 13.82 mm measured

Specifications

Compliance & standards

BS EN 14449 laminated glass · CE / UKCA marked · 24-month panel warranty.

Pairs with

Any PRIVASEE Power Drive family (PJ-C · PJ-D · LD-A · DZ6L · DZD-NO · CZ) sized at 5 W per m². TOSSEAL 381 (LP-003) for frame seal. IPA 70% for cleaning.

Installation

By glazing contractor per BS 6262 / BS 8000-7. Wiring by licensed electrician. PRIVASEE supplies installation method statement and risk assessment on request.

Overview

For balustrades, full-height shopfronts, schools, and any location where impact resistance matters as much as privacy. Same PDLC core, heavier glass on both faces, identical optical performance to SG-01.

Build-up

8 + 0.76 + 0.4 + 0.76 + 8 mm — 16.92 mm typical

Specifications

Compliance & standards

BS EN 14449 laminated glass · CE / UKCA marked · 24-month panel warranty.

Pairs with

Any PRIVASEE Power Drive family (PJ-C · PJ-D · LD-A · DZ6L · DZD-NO · CZ) sized at 5 W per m². TOSSEAL 381 (LP-003) for frame seal. IPA 70% for cleaning.

Installation

By glazing contractor per BS 6262 / BS 8000-7. Wiring by licensed electrician. PRIVASEE supplies installation method statement and risk assessment on request.

Overview

Where partitions need to deliver both visual privacy and measurable noise reduction. Acoustic interlayer + tuned glass thicknesses. Specify your target Rw and we build to it. Range 34–48 dB Rw.

Build-up

varies by Rw target — build-up tuned to spec

Specifications

Compliance & standards

BS EN 14449 laminated glass · CE / UKCA marked · 24-month panel warranty.

Pairs with

Any PRIVASEE Power Drive family (PJ-C · PJ-D · LD-A · DZ6L · DZD-NO · CZ) sized at 5 W per m². TOSSEAL 381 (LP-003) for frame seal. IPA 70% for cleaning.

Installation

By glazing contractor per BS 6262 / BS 8000-7. Wiring by licensed electrician. PRIVASEE supplies installation method statement and risk assessment on request.

Overview

Our highest-clarity grade in self-adhesive form. For when the existing glass has to stay in place — guest rooms, board rooms, refit projects.

Specifications

How to use

Retrofit onto existing glass · wet application with fitter's solution

Application sequence (retrofit)

1. Survey existing glass — measure, note frame condition.
2. Clean glass thoroughly with IPA 70% on lint-free microfibre.
3. Spray glass and film backing with fitter's solution.
4. Peel release liner, apply film to glass, position carefully.
5. Squeegee from centre outward — work all bubbles out.
6. Trim film to glass edge with busbar knife.
7. Expose busbar at film edge — apply silver paint and copper mesh.
8. Connect lead wires (red + / black −) to busbar.
9. Test panel with resistance meter before sealing.
10. Seal glass-to-frame with TOSSEAL 381 silicone.
11. Wire to PRIVASEE Power Drive — commission and sign off.

Compliance

RoHS-compliant materials · CE-relevant components · supplied with batch test data.

Overview

The same T91 grade as the adhesive variant — supplied without backing for vacuum-EVA lamination in our factory. This is the film that goes inside SG-01, LG-01, and LG-AC.

Specifications

How to use

In-house EVA lamination · do not retrofit

Application sequence (retrofit)

1. Survey existing glass — measure, note frame condition.
2. Clean glass thoroughly with IPA 70% on lint-free microfibre.
3. Spray glass and film backing with fitter's solution.
4. Peel release liner, apply film to glass, position carefully.
5. Squeegee from centre outward — work all bubbles out.
6. Trim film to glass edge with busbar knife.
7. Expose busbar at film edge — apply silver paint and copper mesh.
8. Connect lead wires (red + / black −) to busbar.
9. Test panel with resistance meter before sealing.
10. Seal glass-to-frame with TOSSEAL 381 silicone.
11. Wire to PRIVASEE Power Drive — commission and sign off.

Compliance

RoHS-compliant materials · CE-relevant components · supplied with batch test data.

Overview

Slightly more haze than T91 — slightly wider format. The right answer when a single panel needs to span more than 1.8 m without a join.

Specifications

How to use

Retrofit onto existing glass · widths up to 2.0 m

Application sequence (retrofit)

1. Survey existing glass — measure, note frame condition.
2. Clean glass thoroughly with IPA 70% on lint-free microfibre.
3. Spray glass and film backing with fitter's solution.
4. Peel release liner, apply film to glass, position carefully.
5. Squeegee from centre outward — work all bubbles out.
6. Trim film to glass edge with busbar knife.
7. Expose busbar at film edge — apply silver paint and copper mesh.
8. Connect lead wires (red + / black −) to busbar.
9. Test panel with resistance meter before sealing.
10. Seal glass-to-frame with TOSSEAL 381 silicone.
11. Wire to PRIVASEE Power Drive — commission and sign off.

Compliance

RoHS-compliant materials · CE-relevant components · supplied with batch test data.

Overview

Standard-grade lamination film. The everyday choice for SG-01 production where T91-level clarity isn't required.

Specifications

How to use

In-house EVA lamination · do not retrofit

Application sequence (retrofit)

1. Survey existing glass — measure, note frame condition.
2. Clean glass thoroughly with IPA 70% on lint-free microfibre.
3. Spray glass and film backing with fitter's solution.
4. Peel release liner, apply film to glass, position carefully.
5. Squeegee from centre outward — work all bubbles out.
6. Trim film to glass edge with busbar knife.
7. Expose busbar at film edge — apply silver paint and copper mesh.
8. Connect lead wires (red + / black −) to busbar.
9. Test panel with resistance meter before sealing.
10. Seal glass-to-frame with TOSSEAL 381 silicone.
11. Wire to PRIVASEE Power Drive — commission and sign off.

Compliance

RoHS-compliant materials · CE-relevant components · supplied with batch test data.

Overview

For glazing that wants both switchable privacy AND a permanent solar tint when in clear state. Subtle grey, doesn't shift colour temperature inside the room.

Specifications

How to use

Retrofit · combines tint with switchable privacy

Application sequence (retrofit)

1. Survey existing glass — measure, note frame condition.
2. Clean glass thoroughly with IPA 70% on lint-free microfibre.
3. Spray glass and film backing with fitter's solution.
4. Peel release liner, apply film to glass, position carefully.
5. Squeegee from centre outward — work all bubbles out.
6. Trim film to glass edge with busbar knife.
7. Expose busbar at film edge — apply silver paint and copper mesh.
8. Connect lead wires (red + / black −) to busbar.
9. Test panel with resistance meter before sealing.
10. Seal glass-to-frame with TOSSEAL 381 silicone.
11. Wire to PRIVASEE Power Drive — commission and sign off.

Compliance

RoHS-compliant materials · CE-relevant components · supplied with batch test data.

Overview

Where the brief calls for visible solar attenuation as well as privacy. Dark grey reads as architectural, not residential.

Specifications

How to use

Retrofit · stronger solar attenuation

Application sequence (retrofit)

1. Survey existing glass — measure, note frame condition.
2. Clean glass thoroughly with IPA 70% on lint-free microfibre.
3. Spray glass and film backing with fitter's solution.
4. Peel release liner, apply film to glass, position carefully.
5. Squeegee from centre outward — work all bubbles out.
6. Trim film to glass edge with busbar knife.
7. Expose busbar at film edge — apply silver paint and copper mesh.
8. Connect lead wires (red + / black −) to busbar.
9. Test panel with resistance meter before sealing.
10. Seal glass-to-frame with TOSSEAL 381 silicone.
11. Wire to PRIVASEE Power Drive — commission and sign off.

Compliance

RoHS-compliant materials · CE-relevant components · supplied with batch test data.

Overview

For projector rooms, black-box galleries, or any environment where heavy tint plus full privacy matter. Reads as deeply tinted glass when clear, fully opaque when off.

Specifications

How to use

Retrofit · specialist applications

Application sequence (retrofit)

1. Survey existing glass — measure, note frame condition.
2. Clean glass thoroughly with IPA 70% on lint-free microfibre.
3. Spray glass and film backing with fitter's solution.
4. Peel release liner, apply film to glass, position carefully.
5. Squeegee from centre outward — work all bubbles out.
6. Trim film to glass edge with busbar knife.
7. Expose busbar at film edge — apply silver paint and copper mesh.
8. Connect lead wires (red + / black −) to busbar.
9. Test panel with resistance meter before sealing.
10. Seal glass-to-frame with TOSSEAL 381 silicone.
11. Wire to PRIVASEE Power Drive — commission and sign off.

Compliance

RoHS-compliant materials · CE-relevant components · supplied with batch test data.

Overview

The flagship driver. Universal-compat. Customer-selectable matched at factory.

What it does

Drives PRIVASEE PDLC smart film and laminated smart glass panels with a stable low-voltage AC output. Universal-compatible with PRIVASEE film and any third-party PDLC. Operates from standard mains AC input. Output voltage matched to PRIVASEE® Smart Film and Smart Glass at factory specification.

Best for

All standard PRIVASEE projects. Works with any third-party PDLC film too.

Sizing rule

Power requirement is 5 W per square metre of panel area. The driver wattage class must equal or exceed total panel area × 5.

Compliance

CE / UKCA · IEC 61558 short-circuit and overload protection · 24-month warranty.

Indicative price

From $135.00 · subject to project specification and quantity.

Manual + wiring

Full manual (PRIVASEE STRICT international + UAE Local Market editions) and IEC 60617 + 60446 colour-coded wiring drawings supplied with every order.

Overview

Smallest enclosure. For tight installations and retrofits.

What it does

Drives PRIVASEE PDLC smart film and laminated smart glass panels with a stable low-voltage AC output. Universal-compatible with PRIVASEE film and any third-party PDLC. Operates from standard mains AC input. Output voltage matched to PRIVASEE® Smart Film and Smart Glass at factory specification.

Best for

Single-panel residential and small commercial.

Sizing rule

Power requirement is 5 W per square metre of panel area. The driver wattage class must equal or exceed total panel area × 5.

Compliance

CE / UKCA · IEC 61558 short-circuit and overload protection · 24-month warranty.

Indicative price

From $95.00 · subject to project specification and quantity.

Manual + wiring

Full manual (PRIVASEE STRICT international + UAE Local Market editions) and IEC 60617 + 60446 colour-coded wiring drawings supplied with every order.

Overview

One drive, six independently addressable panels.

What it does

Drives PRIVASEE PDLC smart film and laminated smart glass panels with a stable low-voltage AC output. Universal-compatible with PRIVASEE film and any third-party PDLC. Operates from standard mains AC input. Output voltage matched to PRIVASEE® Smart Film and Smart Glass at factory specification.

Best for

Conference rooms, multi-room scenes, partition arrays.

Sizing rule

Power requirement is 5 W per square metre of panel area. The driver wattage class must equal or exceed total panel area × 5.

Compliance

CE / UKCA · IEC 61558 short-circuit and overload protection · 24-month warranty.

Indicative price

From $340.00 · subject to project specification and quantity.

Manual + wiring

Full manual (PRIVASEE STRICT international + UAE Local Market editions) and IEC 60617 + 60446 colour-coded wiring drawings supplied with every order.

Overview

Variable opacity instead of just on/off.

What it does

Drives PRIVASEE PDLC smart film and laminated smart glass panels with a stable low-voltage AC output. Universal-compatible with PRIVASEE film and any third-party PDLC. Operates from standard mains AC input. Output voltage matched to PRIVASEE® Smart Film and Smart Glass at factory specification.

Best for

Galleries, presentation rooms, daylight harvesting.

Sizing rule

Power requirement is 5 W per square metre of panel area. The driver wattage class must equal or exceed total panel area × 5.

Compliance

CE / UKCA · IEC 61558 short-circuit and overload protection · 24-month warranty.

Indicative price

From $280.00 · subject to project specification and quantity.

Manual + wiring

Full manual (PRIVASEE STRICT international + UAE Local Market editions) and IEC 60617 + 60446 colour-coded wiring drawings supplied with every order.

Overview

Built-in radar sensor — auto-trigger on presence.

What it does

Drives PRIVASEE PDLC smart film and laminated smart glass panels with a stable low-voltage AC output. Universal-compatible with PRIVASEE film and any third-party PDLC. Operates from standard mains AC input. Output voltage matched to PRIVASEE® Smart Film and Smart Glass at factory specification.

Best for

Hands-free meeting rooms, motion-activated privacy.

Sizing rule

Power requirement is 5 W per square metre of panel area. The driver wattage class must equal or exceed total panel area × 5.

Compliance

CE / UKCA · IEC 61558 short-circuit and overload protection · 24-month warranty.

Indicative price

From $195.00 · subject to project specification and quantity.

Manual + wiring

Full manual (PRIVASEE STRICT international + UAE Local Market editions) and IEC 60617 + 60446 colour-coded wiring drawings supplied with every order.

Overview

12 V / 24 V DC input — yacht, train, EV, and bus.

What it does

Drives PRIVASEE PDLC smart film and laminated smart glass panels with a stable low-voltage AC output. Universal-compatible with PRIVASEE film and any third-party PDLC. Operates from standard mains AC input. Output voltage matched to PRIVASEE® Smart Film and Smart Glass at factory specification.

Best for

Mobile applications where mains AC is not available.

Sizing rule

Power requirement is 5 W per square metre of panel area. The driver wattage class must equal or exceed total panel area × 5.

Compliance

CE / UKCA · IEC 61558 short-circuit and overload protection · 24-month warranty.

Indicative price

From $215.00 · subject to project specification and quantity.

Manual + wiring

Full manual (PRIVASEE STRICT international + UAE Local Market editions) and IEC 60617 + 60446 colour-coded wiring drawings supplied with every order.

Overview

Bench-top semi-automatic cutter for trimming smart film and PDLC laminated rolls to size before installation.

What it does

Single-blade configuration · for straight precision cuts on film/laminate.

Why it matters

Smart film is less forgiving than gold. Gold can be melted and reused if the form is wrong. PDLC smart film cannot be reworked.

Applications

Film fabrication shops · on-site smart-glass install prep.

Specifications

Max cutting width 2.8 m · single-blade · for straight precision cuts on film/laminate

Indicative price

From $1,570.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

Bench-top semi-automatic cutter for trimming smart film and PDLC laminated rolls to size before installation.

What it does

Single-blade configuration · for straight precision cuts on film/laminate.

Why it matters

Smart film is less forgiving than gold. Gold can be melted and reused if the form is wrong. PDLC smart film cannot be reworked.

Applications

Film fabrication shops · on-site smart-glass install prep · oversize architectural panels exceeding 2.8 m envelope.

Specifications

Max cutting width 3.6 m · single-blade · for straight precision cuts on film/laminate

Indicative price

From $2,050.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

Specialty knife for scoring and exposing the conductive busbar edge on smart film without damaging the ITO layer.

What it does

Used to carefully score and expose the conductive contact area at the film edge without damaging the ITO conductive layer.

How to use it

1. Cut the PDLC smart film to the required project size.
2. Identify the positive and negative busbar/contact sides.
3. Place the film on a clean, flat, dust-free surface.
4. Use the busbar knife carefully along the required edge to expose the conductive contact zone.
5. Keep the blade angle and pressure controlled to avoid damaging the ITO layer.
6. Clean the prepared contact area using the approved method.
7. Apply silver conductive paint to the prepared busbar zone.
8. Allow the silver paint to dry correctly.
9. Apply conductive tape / copper tape.
10. Connect the red and black cables according to the wiring plan.
11. Test the full panel before installation or lamination.

Why it's good

The busbar knife helps the operator prepare the contact zone more accurately than using a normal blade.

Indicative price

From $15.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

Conductive adhesive silver tape used to bond busbar wires to the film's conductive layer.

How to use it

After the PDLC film is cut to size and the busbar/contact edge is prepared, the contact area is cleaned and prepared for electrical connection.

Why it's good

It helps create a cleaner, stronger, and more consistent electrical contact. It reduces the risk of weak contact, partial switching...

When to use it

Use it when preparing PDLC smart film for wiring, whether for self-adhesive smart film installation or non-adhesive PDLC film preparation for EVA laminated smart glass.

Specifications

Conductive adhesive tape · 4 mm wide · 50 m per roll

Indicative price

From $8.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

Conductive adhesive silver tape used to bond busbar wires to the film's conductive layer (wider variant for higher current capacity / larger panels).

How to use it

After the PDLC film is cut to size and the busbar/contact edge is prepared, the contact area is cleaned and prepared for electrical connection.

Why it's good

It helps create a cleaner, stronger, and more consistent electrical contact. It reduces the risk of weak contact, partial switching...

When to use it

Use it when preparing PDLC smart film for wiring, whether for self-adhesive smart film installation or non-adhesive PDLC film preparation for EVA laminated smart glass.

Specifications

Conductive adhesive tape · 10 mm wide · 50 m per roll · for larger panels / higher current

Indicative price

From $15.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

Highly conductive silver paste for sealing busbar contacts and ensuring low-resistance bonds on smart film electrodes.

What it does

Silver conductive paste creates a conductive bridge between the exposed PDLC film contact area and the busbar connection.

How to use it

1. Cut the PDLC smart film to the required size.
2. Prepare the busbar/contact edge using the approved busbar preparation method.
3. Make sure the contact area is clean, dry, and free from dust, oil, adhesive residue, and moisture.
4. Apply a controlled layer of silver conductive paste along the prepared busbar/contact zone.
5. Keep the paste coverage continuous and even.
6. Allow the paste to dry/cure according to the approved production process.
7. Apply conductive tape or copper tape over the prepared area.
8. Connect the red/black lead wires according to the wiring plan.
9. Test the panel for full and even switching before installation or lamination.

Why it's good

Silver conductive paste improves the quality of the electrical contact between the PDLC film and the busbar connection.

When to use it

Use it because PDLC film depends on a clean and stable electrical contact at the busbar area. Without proper conductive connection, the film may not switch at all, or may switch only partially.

Specifications

High-conductivity silver formulation · sold by gram

Indicative price

From $1.20 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

Flexible copper mesh strip used as a conductive bridge or shielding layer in smart film assemblies.

What it does

The copper mesh works as a conductive bridge and reinforcement layer at the PDLC film busbar area. It helps distribute the electrical current and protects the ITO layer from direct heat or pressure damage during welding or wire connection.

How to use it

After the PDLC film is cut and the busbar/contact zone is prepared, the copper mesh is positioned over the prepared conductive area. The connection should be made carefully so that welding or soldering heat does not damage the ITO layer or the active PDLC material.

Why it's good

Copper mesh gives a stronger and safer busbar connection method than connecting directly to a small or fragile contact area on the film edge.

When to use it

Use it when preparing PDLC smart film busbars where stronger electrical contact, heat protection, or reinforcement is required.

Specifications

Flexible conductive copper mesh strip · 30 mm wide · 10 m per roll

Indicative price

From $30.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

The PRIVASEE® Heat Gun is a handheld controlled hot-air tool used mainly to dry silver conductive paint during PDLC smart film busbar preparation.

How to use it

1. Prepare the PDLC film busbar/contact area.
2. Apply silver conductive paint evenly.
3. Set the heat gun to a suitable controlled heat setting.
4. Keep the heat gun moving; do not hold it in one place.
5. Maintain safe distance from the film, cable, and edge area.
6. Dry the silver paint gradually and evenly.
7. Allow the area to cool before applying conductive tape, copper mesh, or cable connection.
8. Inspect the contact area before continuing.
9. Complete wiring and test the full panel switching performance.

Why it's good

It helps speed up and control the drying process for silver conductive paint, making busbar preparation cleaner, faster, and more professional.

Indicative price

From $30.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

Heat-resistant insulated lead wires for connecting smart film busbars to power and switching circuits. Thin high-temperature insulated lead wire for connecting PDLC smart film busbars to power and control circuits.

Why it's good

This wire is good because it combines three important requirements for PDLC production: (1) Thin size — It can be used in tight film-edge and lamination areas without creating bulky cable build-up. (2) Sufficient electrical capacity — It is suitable for PDLC smart film and smart glass lead wiring when used according to the approved panel load and wiring design. (3) High-quality insulation — The insulation is heat-resistant, durable, and difficult to damage during normal production handling.

When to use it

Use this cable because normal wire can be too thick, too weak, or not suitable for hot production areas. PRIVASEE® High-Temperature wire is specifically selected for PDLC smart film and smart glass production.

Specifications

Wire type: high-temperature insulated lead wire · Size: 22 AWG / 0.33 mm² · Roll length: 100 m · Colours: red / black · Insulation: heat-resistant

Indicative price

From $7.50 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

Precision meter for measuring sheet resistance and verifying electrical integrity of smart film before lamination.

What it does

The meter measures electrical resistance across the film's conductive surface or contact area. It helps the technician check whether the ITO conductive layer is still continuous and has acceptable conductivity.

How to use it

1. Place the PDLC film on a clean, dry, flat surface.
2. Identify the ITO/contact test area or busbar preparation zone.
3. Make sure the surface is clean and dry before testing.
4. Touch the meter probes to the required test points.
5. Check the resistance reading.
6. Compare readings across different areas of the film.
7. If resistance is abnormal or inconsistent, inspect for scratches, poor cleaning, broken ITO, weak busbar contact, or other defects.
8. After busbar preparation, test again before wiring.
9. After silver paste / tape / wire connection, test again before final switching test.
10. Record the result as part of QC before installation or lamination.

Why it's good

It helps detect electrical problems before the film is installed or laminated. This saves material, time, and rework because you find the problem early.

Indicative price

From $800.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

3M felt-edge squeegee for pressing film onto glass and pushing out air bubbles during wet/dry application.

What it does

press self-adhesive smart film onto glass · remove trapped air during installation · reduce bubbles · improve film-to-glass bonding · support smooth edge finishing · protect the film surface during pressure application

How to use it

1. Clean the glass fully before installation.
2. Position the self-adhesive PDLC smart film on the glass.
3. Remove the liner gradually as the film is applied.
4. Use the felt-edge squeegee from the centre outward.
5. Push air bubbles toward the nearest edge.
6. Use smooth, controlled strokes.
7. Do not press too hard near the busbar or cable side.
8. Do not use sharp tools to remove bubbles.
9. After installation, check the full surface for bubbles, dust points, lifting, or edge defects.

Why it's good

The felt-edge squeegee is good because it gives the installer better pressure control while protecting the smart film surface from scratches and damage.

When to use it

Use it because PDLC smart film is sensitive during installation. Poor pressure control, hard tools, dust, or trapped air can cause bubbles, lifting, poor adhesion, or surface damage.

Indicative price

From $0.50 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

Capacitive touch switch module used to toggle smart film on/off with a finger tap. Sliding Contact Power Switch / Spring Contact Power Connector — transfers power from fixed frame to moving panel through contact points.

What it does

The sliding contact switch transfers the approved low-voltage smart glass/smart film power or control connection from the fixed frame to the moving panel through contact points. When the contacts touch, the circuit is completed and the smart film or smart glass can operate. When the moving panel separates, the circuit is broken.

How to use it

The fixed contact is installed on the frame, track, wall side, or fixed connection point. The matching contact is installed on the moving panel or glass. When the sliding panel closes or reaches the designed position, the two contacts touch each other and allow the electrical connection to be completed.

Why it's good

It solves one of the main problems in sliding smart glass systems: how to provide power to a moving panel without leaving loose, exposed, dangerous, or unsightly cables.

When to use it

Use it when smart film or smart glass is installed on a sliding or moving panel and the panel needs power only when it reaches a specific position.

Applications

sliding smart glass doors · movable smart glass partitions · smart film on sliding glass · bathroom sliding privacy glass · dressing room sliding privacy glass · office sliding glass partitions · hotel room privacy panels · any smart glass panel where fixed wiring is difficult

Indicative price

From $3.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

Compact mechanical micro switch for inline on/off control of smart film circuits. It is not mainly for carrying power to the smart film. It is used to detect movement or position and send a signal to the controller or relay.

What it does

The micro switch detects physical movement or contact. When the lever/arm is pressed, the internal contact changes state and sends a signal to the system.

How to use it

The micro switch is fixed near the moving part of the door, glass, frame, or mechanism. When the moving part touches or presses the lever/arm, the switch is activated and sends a signal to the controller or relay.

Why it's good

It allows the smart privacy system to react automatically to movement or position, instead of relying only on a manual wall switch.

When to use it

Use it when the smart film or smart glass needs to respond to a physical movement, door position, sliding panel position, or manual trigger.

Indicative price

From $2.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

Reed-style magnetic switch that toggles smart film state based on door or window position. It has two parts: a magnetic piece and a reed contact piece. When the magnet comes close to the sensor, the contact changes state. This makes it useful for hidden or automatic privacy control, especially where physical pressing is not preferred.

What it does

The magnetic switch detects whether a door, window, or sliding panel is open or closed. It can trigger the smart film or smart glass to turn on or off automatically.

How to use it

One part of the magnetic switch is fixed to the frame, wall, track, or fixed side. The matching magnet is fixed to the moving panel or door. When the moving panel reaches the correct position, the magnet aligns with the reed contact. The sensor then sends a signal to the controller.

Why it's good

It gives automatic privacy control without needing the user to press a switch. It is clean, hidden, and useful for sliding privacy glass systems. Because it uses magnetic detection, it avoids the need for a mechanical lever to be pressed, which can be cleaner and more reliable.

When to use it

Use it when smart film or smart glass should react automatically to a door, window, or sliding panel position.

Indicative price

From $4.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

The PRIVASEE® Retractable Cable is a protected extension cable system used to supply the approved power or control connection to sliding doors, moving glass panels, moving smart film, and sliding smart partitions. It is especially useful for sliding doors, moving glass panels, sliding smart partitions, and openable privacy glass where the cable needs to extend and retract with the moving panel.

What it does

The retractable cable provides a flexible protected connection between the controller/driver and the smart film or smart glass panel.

How to use it

The retractable cable box is installed near the sliding track, frame, access panel, or control area. One side connects to the controller/driver. The other side connects to the moving smart film or smart glass panel. When the sliding panel moves, the cable extends with the movement. When the panel returns, the cable retracts back into the housing.

Why it's good

The retractable cable solves a common problem in sliding smart glass systems: how to deliver power to a moving glass panel without leaving exposed, dangerous, or unsightly wires hanging across the opening.

Indicative price

From $9.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

The PRIVASEE® Retractable Cable is a protected extension cable system used to supply the approved power or control connection to sliding doors, moving glass panels, moving smart film, and sliding smart partitions. 2.0 m variant for larger rooms or longer-travel sliding panels.

What it does

The retractable cable provides a flexible protected connection between the controller/driver and the smart film or smart glass panel.

How to use it

The retractable cable box is installed near the sliding track, frame, access panel, or control area. One side connects to the controller/driver. The other side connects to the moving smart film or smart glass panel. When the sliding panel moves, the cable extends with the movement. When the panel returns, the cable retracts back into the housing.

Why it's good

Solves a common problem in sliding smart glass systems: how to deliver power to a moving glass panel without leaving exposed, dangerous, or unsightly wires hanging across the opening.

Indicative price

From $13.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

Hinge accessory with an integrated wire pass-through used for smart glass, smart film, and movable privacy glass doors. It is designed to support moving or opening panels such as frameless glass doors, hinged smart glass doors, pivot doors, folding smart glass panels, and hinged privacy glass systems. The hinge allows the smart glass or smart film panel to receive the approved electrical connection while keeping the wire route hidden and protected.

What it does

The hinge provides both mechanical support and a protected wiring route. Helps: carry the door/panel mechanically · pass the approved low-voltage power or control cable through the hinge area · hide the wire route · reduce loose cable exposure · support smart glass or smart film operation on moving doors · protect the cable from bending, pulling, and door movement damage.

How to use it

The hinge is installed as part of the door or panel hardware. The cable is routed through the hinge channel or hinge-side compartment. The cable path must be planned before fabrication so the wire exit, hinge position, frame route, and controller location are all coordinated.

Why it's good

It solves a common problem in smart glass doors: how to power a moving door without visible loose wires. It gives a cleaner architectural finish and helps protect the cable route. It is better than leaving a wire hanging across the door opening.

When to use it

Use it when smart film or smart glass is installed on a moving hinged, pivoting, folding, or opening door and the electrical connection needs to be hidden or protected.

Indicative price

From $30.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

PRIVASEE® Spring Wire 3 m is a flexible coiled cable used to carry power or control wiring to movable smart glass, smart film, and movable privacy glass systems. It is used where the smart glass or smart film panel is not fixed in one position, such as sliding doors, swing doors, pivot doors, and moving smart glass partitions.

What it does

This cable allows the electrical connection to stay active while the panel moves. Helps: transfer power or control signal to a moving smart glass / smart film panel · extend when the door or panel opens · retract when the panel closes · reduce cable slack and loose cable mess · protect the wiring path better than a normal straight wire

Why it's good

A normal straight cable can hang loosely, rub, twist, or be damaged as the panel moves. The spring cable is better because it stays organized, protected, and ready for repeated movement.

Specifications

Coiled / spiral spring cable construction · standard length 3 m · flexible extend-and-retract design · suitable for repeated movement · black coiled outer · low-voltage smart glass / smart film wiring routes

Indicative price

From $3.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

The PRIVASEE® Wire Cross Tube is a small cable-routing accessory used to pass smart film or smart glass wiring neatly through frame intersections, corners, and complex architectural details. It helps guide and protect the wire as it crosses from one frame section to another, especially where the cable needs to change direction, hide inside frames, or pass through partition junctions.

What it does

The Wire Cross Tube creates a protected pass-through path for smart film / smart glass cables. Helps: route wires through frame intersections · protect cables from sharp aluminum or glass edges · hide wiring inside the frame or partition system · keep the installation clean and professional · reduce cable bending, rubbing, and damage · support neat cable transition between profiles or panels

How to use it

The tube is installed at the cable crossing point before final wiring is completed. The installer routes the smart film or smart glass cable through the tube. The cable must pass smoothly through the tube without being pinched, cut, over-bent, or stretched.

Why it's good

It protects the cable and improves the installation finish. Without a pass-through tube, wires can rub against sharp frame edges, get pinched, or create a messy appearance.

When to use it

Use it when the smart film or smart glass cable needs to cross through a frame, partition junction, door frame, or hidden architectural detail.

Applications

frame corners · aluminum profile intersections · partition junctions · sliding or hinged door frame areas · cable exit points · hidden wiring routes

Indicative price

From $5.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

Aluminium-framed variant of the Wire Cross Tube — for embedded installations where the tube is fitted into a structural frame element.

What it does

Creates a protected pass-through path for smart film / smart glass cables, with frame-integrated mounting.

How to use it

Same as the no-frame variant — installed at cable crossing point before final wiring. The framed mount accepts standard aluminium profile fixings.

Why it's good

Adds structural integration to the cable pass-through — for premium architectural details where the tube becomes part of the frame finish.

Indicative price

From $7.50 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

PRIVASEE® Vacuum Bag Sealant Tape is a soft sealing tape used to close and seal the edges of the vacuum bag or vacuum sealing film so the vacuum system can remove trapped air and moisture from the glass/PDLC panel assembly during lamination.

What it does

The tape creates an airtight edge seal for the vacuum bag. Helps: seal the vacuum bag edges · keep vacuum pressure stable · prevent air leakage during lamination · help remove trapped air from the panel build-up · support better EVA bonding · reduce bubbles and air pockets · improve smart glass lamination quality

How to use it

After the glass, EVA, PDLC film, EVA, and glass layers are assembled, the panel is wrapped or covered with vacuum sealing film or bag. The vacuum hose or connector is then attached, and the panel is connected to the vacuum system. Before heating, the vacuum edges must be sealed with the sealant tape.

Why it's good

It helps create a strong, airtight vacuum bag seal. A proper seal improves vacuum stability and supports cleaner lamination quality.

When to use it

Use it because vacuum quality is one of the most important parts of EVA smart glass lamination. The sealant tape helps ensure that the vacuum can work effectively and achieve better lamination results.

Applications

EVA laminated PDLC smart glass · panel-by-panel vacuum sealing · large glass panels · premium smart glass production · reducing lamination defects · improving factory QC

Indicative price

From $3.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

Paired male and female quick-disconnect connectors used for PRIVASEE® smart film and smart glass wiring. They provide a clean, serviceable disconnect between film leads and driver wiring.

When to use it

Use it when the smart film or smart glass may need to be disconnected for testing, transport, display, maintenance, or rework. They are especially useful for sample panels, demo kits, testing, training, and temporary display setups, because the panel can be easily connected and disconnected without cutting wires.

Applications

Sample smart film panels · Demo smart glass panels · Showroom display panels · Training kits · Testing before final installation · Temporary exhibition/demo wiring · Quick-disconnect at transformer or driver · Field-serviceable wiring · Panel replacement or maintenance

Indicative price

From $5.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

PRIVASEE® Dustless Paper is a lint-free cleaning tissue used during PDLC smart film and smart glass preparation. It is used before smart film installation, before lamination, and during busbar preparation to keep the working area clean.

What it does

remove dust from glass before smart film installation · clean the PDLC film surface during preparation · clean the busbar/contact zone before silver paste or conductive tape · reduce fiber and lint contamination · support better adhesive bonding · reduce bubbles caused by trapped particles · improve lamination cleanliness · support professional workshop QC

How to use it

Use the dustless paper on a clean, dry surface. Wipe the glass or film area gently in one direction, not in dirty circular motions. For busbar preparation, use it to clean the contact area before applying silver paste, conductive tape, copper mesh, or other materials.

Why it's good

Normal tissue or paper can leave fibers, lint, or dust on the glass or film surface. These particles can become trapped under the film and cause permanent defects.

When to use it

Use it because clean preparation is one of the most important steps in smart film and smart glass work. A very small particle trapped during installation or lamination can ruin the entire panel.

Why it matters

Dustless paper is important because PDLC smart film is highly sensitive to contamination. Small dust particles, fibers, or lint can become trapped under the film, in the busbar area, or during lamination, and cause bubbles, weak adhesion, or poor electrical contact.

Indicative price

From $2.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

The PRIVASEE® Rail and Track System is a sliding hardware and cable-management system used for movable smart glass, smart film, and smart privacy glass doors. It supports the movement of sliding smart glass doors or movable privacy panels while helping route the required electrical connections.

What it does

The rail and track system helps: support sliding movement of smart glass panels · guide movable privacy panels · carry or manage the panel movement path · support cable routing or contact connection along the sliding area · reduce loose wiring around moving glass · create a cleaner installation for smart sliding doors and partitions · support movable office partitions and privacy glass systems

How to use it

The track is installed in the approved sliding-door or partition position. The roller or carriage is fitted to the smart glass or smart film panel. The panel must slide smoothly without pinching, pulling, crushing, or damaging the cable.

Why it's good

It allows smart glass and smart film systems to be used on moving panels, not only fixed glass. This is important for sliding doors, movable partitions, and flexible privacy installations. It gives a more professional finish than exposed cables or improvised wiring.

When to use it

Use it when a smart glass or smart film panel needs to slide or move while still being connected to the control system.

Applications

sliding smart glass doors · sliding smart film panels · movable office partitions · smart privacy room doors · hotel privacy glass · bathroom sliding glass · dressing-room privacy doors · meeting-room sliding partitions · movable smart glass display panels

Specifications

Roller sold per piece · Can work with extension box, spring wire, retractable cable, or contact connector systems

Indicative price

From $9.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

Aluminium sliding-door track. Cut to length per project. Used with rail roller for sliding-door PDLC partitions.

What it does

Same as the rail-and-track-system roller — supports sliding movement of smart glass / film panels. Track sold per linear metre.

How to use it

Track installed in the approved sliding-door or partition position. Cut to project length.

Specifications

Aluminium sliding track · per linear metre · cut to project length

Indicative price

From $8.00 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.

Overview

PET Film used for vacuum sealing each glass panel before EVA lamination. Each panel can be connected individually to vacuum.

Specifications

PET Film for vacuum sealing · widths 1m / 1.3m / 1.6m / 1.8m / 2.0m · sold per kg

Indicative price

From $2.45 each · subject to project quote.

Direct from PRIVASEE® Group

UK-engineered · UAE-distributed · authorised distributors only · 12-month warranty on tools and equipment.